Free in-home measure and quote - PGT, CGI and CWS impact lines compared on your actual openings, style by style
Sliding glass doors
Impact garage doorsPGTCGI
Before
After
Before
After
Before
AfterMr-Glass Custom & Geometric Windows in Deerfield Beach: What to Know First
We repair and replace Mr-Glass custom and geometric windows in Deerfield Beach as an independent Mr-Glass service provider, and most jobs are completed in a single visit. Custom shapes cost more than standard rectangles, period. A typical geometric window repair runs $350 to $900, while full replacements of arched or shaped units in Deerfield Beach usually land between $900 and $2,800 depending on glass type, frame condition, and whether the opening is oversized.
This page is for homeowners in Deerfield Beach who own Mr-Glass windows that are fogged, leaking, binding, or showing seal failure on a shaped or arched unit. If that’s you, call (786) 743-5882 and a live person will answer. You won’t get a voicemail tree.
How Mr-Glass Products Fail - and How We Fix Them
Mr-Glass built a reputation in South Florida for custom shapes at a fair price. We see a lot of their work in Deerfield Beach, especially in the older neighborhoods west of Dixie Highway and around the Cove. Here’s what actually goes wrong, series by series, and what we do about it.
- Seal failure on Mr-Glass custom radius units. Curved and arched insulated glass carries more stress at the bend than flat glass. Over years in Deerfield Beach humidity, the seal at the curve is the first thing to let go. You get fog between the panes that won’t wipe off. We replace the insulated glass unit with a new one cut to the exact radius, not a field-bent approximation.
- Frame deflection on oversized geometric openings. Mr-Glass made some large trapezoid and hexagonal windows for Deerfield Beach homes built in the 1990s and early 2000s. The aluminum used on certain mid-tier lines was thinner than what we’d spec today, and on a wide span the frame sags just enough to make the sash bind. We shim, re-square, and re-bed the frame, and if the extrusion is too far gone we quote a replacement in heavier-gauge aluminum.
- Weep-hole blockage on Mr-Glass casements and awnings with custom glazing. Deerfield Beach gets real wind-driven rain. When weep holes clog with salt and grit, water sits in the track and eventually finds the interior. We clear the weep system and re-slope the sill if needed, then test with a garden hose before we call the job done.
- Glass-to-frame seal deterioration on painted finishes. Mr-Glass units with factory-painted frames, especially white, develop a brittle bond where the glazing tape meets the paint after six to ten years in coastal air. The symptom is a hairline gap you can feel as a draft. We strip the old tape, clean the seat, and re-glaze with a marine-grade setting tape rated for South Florida exposure.
- Stress cracks in Mr-Glass tempered shapes. A tempered trapezoid or radius unit that wasn’t handled perfectly at install can carry a micro-fracture at an edge. It holds for years, then one afternoon you hear a pop and there’s a crack running from the corner. We see this regularly in Deerfield Beach homes with west-facing geometric windows that take hot afternoon sun. The fix is a new tempered lite cut to the shape, installed with the edge clearance the original should have had.
Our Mr-Glass Custom & Geometric Windows Process
Every Mr-Glass job in Deerfield Beach follows the same steps, and Dale Kessler still insists on the first one himself: measure twice before ordering anything. If it is not in the contract, it is not in the scope.
- 1
We measure the opening, not the old glass. Glass can shift in the frame over time. We pull dimensions from the rough opening and the reglet, then verify the shape with a template for radius and angle work.
- 2
We identify the failure in plain terms. You’ll hear exactly what went wrong, why it happened in Deerfield Beach’s climate, and whether a repair will hold. No mystery, no upselling.
- 3
We quote OEM and quality aftermarket side by side on paper. For Mr-Glass units, OEM insulated glass is sometimes still available through regional suppliers. When it isn’t, we source from glass fabricators who cut architectural shapes regularly, and we tell you the difference before you spend a dollar.
- 4
We do the work in one visit when the glass is ready. The unit arrives pre-cut. Our technicians set it, shim it, seal it, and re-install the stops without rushing the cure time on the setting tape.
- 5
We test and walk you through it. A hose test on the exterior, a close look at the interior, and a straight answer about how long the fix should last.
- 6
We register the warranty before the truck leaves. Every job is covered by the Done Right Promise and The Keystone Standard. Both manufacturer warranty layers get registered in writing, durations stated, no arguing later.
What Mr-Glass Custom & Geometric Windows Costs in Deerfield Beach
Here are the numbers we actually see on Mr-Glass work in Deerfield Beach:
- Seal failure repair on a custom shape: $350-$700 for a standard arch or radius under 40 inches. Larger units run higher.
- Full replacement of a Mr-Glass geometric window: $900-$2,800 depending on size, shape complexity, glass package, and frame condition.
- Oversized openings (anything over 60 inches on the long side): $2,200-$5,000 plus, because the glass is heavier, the frame needs more reinforcement, and the install takes two technicians.
- Parts-only work like sweep replacement or weep clearing: $150-$450.
What moves the price: whether the glass is tempered or laminated (impact shapes cost more), whether the frame is salvageable, and whether the opening needs re-squaring before new glass goes in. We give written line-item quotes, and the price we hand you is the price you pay. Call (786) 743-5882 for a free estimate. No surprise line items, ever.
Why Deerfield Beach Homeowners Call TruePane Windows & Doors for Mr-Glass Work
We’ve been doing this in Deerfield Beach since 2008, and Dale Kessler grew up a few blocks from Quiet Waters Park, so he knows what salt air does to aluminum frames and glass seals that were never right to begin with. We train our own apprentices into journeymen, we hire local, and every technician who walks into your home is background-checked and uniformed. If a Mr-Glass unit is beyond saving, we also service and install PGT, CGI, CWS, and ES Windows, so you get an honest comparison instead of a sales pitch for one brand. A live person answers our phone 24 hours a day, 7 days a week. We show up when we say we will, and we stand behind the work in writing.
FAQs
Some Mr-Glass insulated glass units are still available through regional suppliers, but many custom shapes are not, so we work with architectural glass fabricators who cut radius and angle units on order. We’ll quote OEM when it exists and tell you plainly when aftermarket is the better call. Call (786) 743-5882 and we’ll check your specific unit.
If the frame is square and the glass is the only failure, a repair costs less and lasts as long as the original unit did. If the frame is deflecting or corroded, replacement is the honest answer. We’ll show you both numbers and let you decide. Estimates are free.
Most repairs take one visit, typically two to four hours, once the replacement glass is fabricated and in our hands. Fabrication for custom shapes usually takes five to ten business days. We’ll confirm a date before we schedule the truck.
No. We quote the job in writing before we begin, and our Done Right Promise means the work is guaranteed for 90 days with no paperwork fights. If we find hidden damage mid-job, we stop and talk to you before anything changes.
Written by Dale Kessler, Owner, TruePane Windows & Doors at TruePane Windows & Doors, serving Deerfield Beach and nearby areas.
Six Reasons Homeowners Choose TruePane Windows & Doors
Impact systems engineered to design pressures up to +/-100, matched to your wind zone - your openings hold when the storm arrives.
Low-E insulated impact glass from our manufacturer lines commonly cuts monthly cooling bills 20-30%.
Laminated impact glass shuts out up to 40% of outside noise - traffic, neighbors, weather.
Monitoring services run $30-90 a month. Laminated impact glass resists forced entry around the clock, with no subscription.
Florida homeowners average around 25% savings on the windstorm portion of their policy after protecting every opening - some homes qualify for more.
A full impact package upgrades curb appeal, buyer confidence and appraised value in one project.