CGI Door Installation Nationwide | TruePane Windows & Doors

CGI Door Installation: The Deerfield Beach Owner’s Guide

If you have a CGI door with a failed component, the question usually isn’t whether to fix it. It’s whether the person doing the work knows CGI hardware well enough to match the part, shim the door true, and not void your impact rating in the process. A complete CGI door installation in Deerfield Beach typically runs $450-$1,150 installed depending on whether we’re swapping hinges, a lock set, weatherstripping, or the full slab. Most jobs are done in one visit because we stock the common CGI-compatible hardware on the truck. You’ll usually know something’s wrong when the door starts dragging at the threshold, the deadbolt won’t throw clean, or you can see daylight through the weatherstrip on the hinge side.

Call (786) 743-5882

Key Takeaways:

• CGI doors use reinforced hardware built for impact ratings; generic big-box parts often don’t match the hinge geometry or throw length.
• Salt air in Deerfield Beach shortens weatherstripping and hinge life faster than inland installations.
• We quote the part and the labor separately on paper, so you see exactly what you’re paying for.
• The work is covered by our Done Right Promise, and we register every manufacturer warranty layer before we leave.

Which CGI Models This Applies To

CGI builds impact-rated entry doors, French doors, and sliding glass doors, and the installation hardware varies by series. The most common lines we service in Deerfield Beach are the Estate Collection, the Tribute Series, and the Sentry line. Each uses proprietary hinge patterns and multi-point lock bodies that don’t always swap with off-the-shelf parts. Here’s the gotcha most homeowners run into: CGI’s multi-point lock systems changed throw lengths between certain production years, so a lock ordered for a 2012 Estate door will not seat correctly in a 2019 Estate door even though both are labeled the same series. We check the door’s manufacturing label on the hinge edge, measure the existing hardware, and match it to the exact CGI spec or a proven aftermarket equivalent before cutting anything.

On the OEM-vs-aftermarket decision: for hinges, strike plates, and guide blocks, quality aftermarket parts from suppliers like Truth Hardware and Hager often match or exceed spec while costing 20-30% less. For multi-point lock bodies and astragals, we stay OEM. Those carry the impact-load geometry, and the savings on an aftermarket substitute isn’t worth a door that binds before the first hurricane season is over. We are an independent service provider, not a CGI dealer, which means we stock parts from CGI, Andersen, and Pella and recommend what fits your door correctly, not what pads a franchise quota.

Signs Your CGI Door Installation Is Failing

• Door drags or scrapes at the threshold. In a coastal climate, the slab settles and the frame shifts slightly with humidity swings. A door that started binding only in July may have a sagging hinge or a misaligned strike, and forcing it will chew up the weatherstrip and the threshold cap.
• Deadbolt won’t throw without lifting the handle. This usually means the lock body and the strike plate are no longer aligned because the door has settled or a hinge pin is worn. On a CGI door with a multi-point lock, this also means the side bolts aren’t fully engaging, which quietly reduces the impact rating you’re counting on.
• Visible daylight at the corners or hinge side. Salt air and UV break down CGI’s weatherstrip compound faster in Deerfield Beach than the manufacturer’s average lifespan suggests. Once the seal compresses permanently, water follows it. We’ve pulled more rotted bottom rails out of doors in Pompano and Lighthouse Point than we can count, and nearly all of them started with a $40 weatherstrip.
• Door slams shut on its own or won’t stay open. This points to hinge wear or a frame that’s no longer plumb. CGI slabs are heavy, and when gravity gets more traction than the hinge geometry, every cycle grinds the pins down further.
• You hear wind whistle at the lock stile during storms. That’s the astragal or interlock weatherstrip failing. It’s not just a draft. On an impact-rated door, the interlock seal is part of the water-intrusion defense. If you’re hearing the wind, water is moments behind it in a tropical system.

Replacement Cost & What’s Included

For Deerfield Beach homeowners, here’s the line-item picture on a CGI door installation:

• Hinge replacement (3 hinges, ball-bearing, stainless): $140-$280 installed
• Multi-point lock body replacement (OEM CGI): $320-$560 installed
• Weatherstripping and threshold cap refresh: $90-$210 installed
• Full slab swap with hardware transfer and re-shim: $650-$1,150 installed
• Frame-to-hinge-side adjustment and strike realignment: $110-$190 installed

Every quote separates the part from the labor on paper, and the number we give you is the number on the invoice. No change orders, no surprise line items. The Done Right Promise means if the door binds, drags, or the lock doesn’t throw clean within ninety days, we return and make it right, no arguing. The Keystone Standard means both the part manufacturer’s warranty and our workmanship warranty are registered in writing before the truck leaves your driveway. That’s a square deal, and it’s how we’ve worked in South Florida since 2008.

DIY or Call Us?

A homeowner with a level, a screwdriver, and patience can replace a threshold cap or clean and lubricate a lock cylinder. Those are safe, straightforward jobs and we encourage them if you’re comfortable. What we don’t recommend is attempting a multi-point lock body replacement or adjusting a CGI slab on your own. Full-lite impact doors can weigh 180-250 pounds, and when one shifts off its hinges during a panel swap, it does real damage to floors, feet, and fingers. We’ve also seen well-intentioned DIYers drill new strike holes in the frame to “fix” a misaligned lock, which only weakens the jamb and voids the impact certification. That one costs more to correct than the original repair. If the job requires pulling hinge pins or moving the slab, call (786) 743-5882. Dale Kessler grew up near Quiet Waters Park and he’s spent a career reading rough openings honestly. We’ll quote it straight and do it once.

FAQs