Free in-home measure and quote - PGT, CGI and CWS impact lines compared on your actual openings, style by style
Sliding glass doors
Impact garage doorsPGTCGI
Before
After
Before
After
Before
AfterCWS Door Installation in Deerfield Beach: What to Know First
CWS door installation in Deerfield Beach typically runs $900 to $3,400 per opening depending on whether we’re setting a standard single entry, a double French, or a custom arched unit into an existing rough opening. TruePane Windows & Doors is an independent CWS service provider, not a manufacturer affiliate, and most single-door jobs are completed in one visit, with the workmanship guaranteed 90 days under our Done Right Promise. If you own a CWS door that binds, leaks, or simply was never set true, this page tells you what’s actually going on and what it costs to correct. Call (786) 743-5882 and a live person answers.
How CWS Products Fail - and How We Fix Them
CWS doors are good products, but Deerfield Beach’s salt air and seasonal humidity will expose any installation shortcut within a few years. Here’s what we see most often on CWS jobs, including the symptoms that don’t show up on a spec sheet.
- CWS Sentinel series entry doors with sagging slabs. These steel and fiberglass units are heavy, and if the installer set the hinges without shimming the jamb, the slab drifts until the latch no longer lines up. The real cause is usually hinge screws into drywall only, not the rough frame. Our fix involves pulling the casing, setting the jamb plumb on shims at every hinge point, and re-hanging with 3-inch screws into the king stud.
- CWS vinyl swinging doors binding every July. Vinyl expands with coastal heat and humidity. When a door is set with no expansion clearance on the latch side, the slab seizes against the jamb and the homeowner starts forcing it. We re-set the door with the manufacturer’s required clearance and replace any weatherstripping that’s been crushed flat.
- CWS sliding patio doors with worn OEM rollers. The earlier CWS roller assemblies were nylon wheels on steel axles. Salt air gets into the track and the axles corrode, so the door gets hard to move at roughly the ten-year mark. We replace them with sealed-bearing stainless steel aftermarket rollers that outlast the originals. The old parts get handed to the homeowner, not tossed in the truck.
- CWS double French units that will not close square. Both panels were hung before the center was shimmed, so the active leaf has to be lifted to latch it. That is a rough-opening issue, not a manufacturing defect. We pull both slabs, correct the sub-sill shimming, and re-hang with even top reveals.
- Arched CWS doors with cracked glass near the frame. These custom-radius glass units get stress fractures when the frame is racked during install, usually because the opening wasn’t checked for square and level first. The glass company will call it thermal stress. We call it a frame that was twisted. Our install stops if the rough opening is out of true until it’s corrected, because no door made can sit right in a racked opening.
One thing you won’t find on CWS’s own website: the foam weatherstripping on their mid-2010s swing doors degrades badly in direct afternoon sun, the west-facing exposures especially. By year seven, that foam turns brittle and starts wicking water. If the door is otherwise solid, we swap in a high-density silicone replacement and re-tension the sweep. That’s a few hundred dollars versus replacing the whole unit.
Our CWS Door Installation Process
We’re a second-generation glazier’s shop, and on a CWS job in Deerfield Beach, the process is the same plain sequence every time.
- 1
Inspection of the rough opening, not just the slab. We check the king studs, sill, and header before we talk about doors. If the frame is not true, nothing we hang on it will stay true. If it is not in the contract, it is not in the scope.
- 2
Parts decision in front of you. If it’s OEM, we say so and price it. If an aftermarket part will outlast the original, we say that too and show you why. You approve before we order.
- 3
Set, shim, level, plumb, repeat. Every hinge point is shimmed, every reveal is checked with a folding rule, not just a laser, and the slab is closed and latched before we drive the final pins.
- 4
Seal and flash correctly for salt air. Deerfield Beach’s salt exposure means we use marine-grade sealants around door frames and check that the sill pan drains properly. You can’t caulk your way out of a bad sill.
- 5
Test the throw, the sweep, and the weatherseal. The door has to close with one finger, latch without lifting, and seal tight on all three sides with no daylight showing.
- 6
Cleanup and paperwork. We walk the threshold with you, hand you the old parts, and leave the written warranty registration before the truck leaves. Done Right Promise applies, no fine print arguing.
What CWS Door Installation Costs in Deerfield Beach
Straight talk on numbers. CWS door installation in Deerfield Beach runs from about $900 to $3,400 depending on what’s being set and what shape the opening is in.
| Job Type | Typical Range | What Moves It |
|---|---|---|
| Single CWS entry door, standard opening | $900 - $1,500 | Jamb condition, trim rework |
| CWS double French doors | $1,800 - $2,800 | Slab weight, sill work, shimming |
| CWS sliding glass door | $1,200 - $2,200 | Roller replacement, track bed |
| CWS arched or custom door | $2,400 - $3,400 | Radius shimming, glass setting time |
What moves the price: a rotted sub-sill that has to be rebuilt, out-of-square framing that needs correcting, or site conditions like upper-floor carry. Every bid is line-item on paper before work begins. If it is not in the contract, it is not in the scope. Call (786) 743-5882 for a free written estimate.
Why Deerfield Beach Homeowners Call TruePane Windows & Doors for CWS Work
We’re an independent CWS service provider that also handles Andersen, Pella, and PGT. That breadth matters because it means we’re never trying to force one brand into a job it doesn’t fit. For years we’ve served this community. Dale Kessler grew up a few blocks from Quiet Waters Park, learned the trade at Broward College, and worked residential jobs along the A1A corridor before opening TruePane in 2008. He’s still the one who reads rough openings honestly, and he still measures twice, because his father was a glazier too. If the pane is not true, the job is not done. Every CWS install gets The Keystone Standard: both warranty layers registered in writing, durations stated, before the truck leaves. And if it’s not done right, we make it right. That’s the Done Right Promise, no paperwork fights.
FAQs
Yes, as an independent CWS service provider we install to manufacturer specs and register both warranty layers in writing before the truck leaves. If a part failure is covered, we handle the claim and do the labor on schedule.
Most OEM CWS hardware and weatherseal components arrive within five to seven business days. We stock high-use aftermarket replacements like rollers and sweeps on the truck for same-day fixes. Call (786) 743-5882 and we’ll tell you what’s available for your exact model.
If the slab and glass are sound, repair is almost always the better call, especially for hardware and seal failures. When the frame is racked or the rough opening has rotted, replacement makes more sense. We’ll show you the numbers both ways before you commit.
Yes, including roller and track replacement, weatherseal reconditioning, and full slab resets. Sliding doors take the worst of Deerfield Beach’s salt and humidity, so we use corrosion-resistant hardware on every one.
Call TruePane Windows & Doors at (786) 743-5882. You’ll get a live person, straight numbers, and a door that’s set true the first time.
Written by Dale Kessler, Owner, TruePane Windows & Doors at TruePane Windows & Doors, serving Deerfield Beach and nearby areas.
Six Reasons Homeowners Choose TruePane Windows & Doors
Impact systems engineered to design pressures up to +/-100, matched to your wind zone - your openings hold when the storm arrives.
Low-E insulated impact glass from our manufacturer lines commonly cuts monthly cooling bills 20-30%.
Laminated impact glass shuts out up to 40% of outside noise - traffic, neighbors, weather.
Monitoring services run $30-90 a month. Laminated impact glass resists forced entry around the clock, with no subscription.
Florida homeowners average around 25% savings on the windstorm portion of their policy after protecting every opening - some homes qualify for more.
A full impact package upgrades curb appeal, buyer confidence and appraised value in one project.