Mr-Glass Door Installation Nationwide | TruePane Windows & Doors

Mr-Glass Door Installation in Deerfield Beach: What to Know First

Mr-Glass door installation in Deerfield Beach typically runs between $850 and $2,400 for a standard replacement, with most jobs completed in one visit. We’re an independent Mr-Glass service provider, which means we install, repair, and replace Mr-Glass doors without being tied to any single manufacturer’s parts channel. If you own a Mr-Glass entry door or French door that binds in summer or drafts in January, call (786) 743-5882 and we’ll give you a straight answer about what it needs.

Call (786) 743-5882

This page is for homeowners in Deerfield Beach who bought a Mr-Glass door years ago and now face a decision: repair it, replace it, or live with it. We’ll walk through what actually goes wrong with these doors, what it costs to fix them in this market, and how we approach the work. No runaround, no inflated estimates, no pushing a replacement when a repair will do.

How Mr-Glass Products Fail - and How We Fix Them

Every door line has its own weak points. Mr-Glass doors are no different. Here’s what we see on Deerfield Beach homes, and what we do about it.

• Sagging hinges on Mr-Glass French doors. The Mr-Glass french door series uses a hinge design that holds up reasonably well, but after eight to ten years of coastal humidity, the hinge screws can back out of the jamb. The door starts dragging on the threshold at the strike side. We pull the door, repair or replace the hinge mortises with hardwood Dutchmen, and rehang it so the reveal is even top to bottom. It’s the difference between a door that closes with one finger and one that needs a shoulder.
• Threshold rot on entry doors with south-facing exposure. Deerfield Beach homes that face the ocean get driven rain, and a Mr-Glass entry door’s threshold takes the brunt. The aluminum threshold is fine, but the substrate underneath is often wood that was never properly flashed. We pull the threshold, inspect what’s underneath, replace any rot with composite material, and flash it so water drains away from the house rather than into it.
• Weatherstripping degradation on Mr-Glass storm doors. The foam and vinyl gaskets on Mr-Glass storm doors break down faster in salt air than they do inland. A door that was weathertight three years ago starts leaking air around the latch side. The fix is straightforward: we replace the gaskets with a denser commercial-grade material that holds up longer in coastal conditions, and we adjust the strike plate so the door compresses the seal evenly.
• Glass seal failure in Mr-Glass door lites. Mr-Glass door glass uses a dual-pane insulated unit, and when the seal fails you get condensation between the panes. You cannot clean that away. The glass unit has to be replaced. We order a new IGU sized to the door’s exact rough opening, and we match the low-E coating so the new glass looks right next to the old. In Deerfield Beach, where humidity sits high most of the year, we see seal failures earlier than inland installations.
• Loose handle sets on Mr-Glass entry doors. The handle set on a Mr-Glass entry door is straightforward to replaceif you have the right backset measurement. We see doors where someone installed a generic handle set that never quite fit the Mr-Glass prep holes. The result is a handle that wobbles and eventually strips the screws. We install a properly sized handle set, reinforce the prep holes with threaded inserts, and set the latch so it engages the strike plate cleanly.

Our Mr-Glass Door Installation Process

Here’s how a typical Mr-Glass door installation goes when you call us in Deerfield Beach.

1. 1
   We answer the phone. A live person picks up, day or night. You describe the door, what it’s doing, and when it started. We schedule a visit.
2. 2
   We measure everything twice. Dale Kessler keeps a folding rule in his truck for a reason. Lasers are fast, but a steel rule never lies. We measure the rough opening, the door slab, the reveals, and the threshold height.
3. 3
   We give you a written decision. If the door can be repaired, we tell you exactly what it needs and what it costs. If it’s a replacement, we quote manufacturer lines side by side on paper, including Mr-Glass if that’s what you want, plus comparable options like PGT or CGI if you want to see the difference. No vague “we’ll see when we get in there” pricing.
4. 4
   We do the work in one visit. Most Mr-Glass door installations are completed the same day. The old door comes out, the opening gets inspected and prepped, the new door goes in, and the hardware is set. If we find hidden damage to the rough opening, we show it to you before we touch anything.
5. 5
   We test the door before we leave. Open, close, open, close. We check the reveal, the latch, the weatherstrip compression, and the sweep. If the door doesn’t close true, we adjust it until it does. The founding rule is simple: if the pane is not true, the job is not done.
6. 6
   We register the warranty in front of you. Before the truck leaves your driveway, both manufacturer warranty layers are registered in writing, durations stated. That’s The Keystone Standard, and it applies to every job, including repairs.

What Mr-Glass Door Installation Costs in Deerfield Beach

Straight numbers, based on what we’ve quoted on Deerfield Beach jobs over the past several years.

What moves the price: whether the rough opening needs repair, the door’s size (custom sizes cost more than standard 36-inch by 80-inch entries), the hardware you choose, and whether you want impact-rated glass. We don’t pad the bill with surprise line items, and we don’t push a high-end replacement when a repair will put your door back in service for years. Estimates are free. Call (786) 743-5882 for an exact quote on your Mr-Glass door.

Why Deerfield Beach Homeowners Call TruePane Windows & Doors for Mr-Glass Work

We’re not a franchise. We’re not the cheapest bid. We’re a local company with years of community service behind us, built by a second-generation glazier who grew up a few blocks from Quiet Waters Park and watched salt air eat aluminum frames off houses that should have been reglazed years earlier. Dale Kessler learned the trade at Broward College’s construction technology program and spent years working residential jobs up and down the A1A corridor before starting TruePane. He reads a rough opening honestly, and he’ll tell you what the frame actually needs rather than what keeps the estimate low enough to win the job. If it is not in the contract, it is not in the scope.

On Mr-Glass work specifically, our technicians know the product’s failure modes and fix them correctly the first time. We’re also authorized installers for more than a dozen other lines, including PGT, CGI, CWS, and ES Windows. If your Mr-Glass door is beyond repair and you want to see alternatives side by side, we’ll put the quotes on paper so you see exactly what you’re buying. Every job is covered by the Done Right Promise: if it is not done right, we make it right. No paperwork fights, no arguing, no fine print that covers neither.

FAQs